In this article, copper (Cu) crystallites were successfully prepared via low temperature molten salt method, and the possible formation mechanisms were proposed. The conductive fillers of multiwalled carbon nanotubes (MWCNTs) and as-prepared Cu particles were designed and introduced into acrylonitrile-butadiene-styrene (ABS) blend to prepare different conductive composites. The dispersion states of conductive fillers and the morphologies of the composites were characterized using a field emission scanning electron microscope. The electrical resistivity of different composites was measured. The results showed that Cu and MWCNTs exhibited a synergistic effect in decreasing the electrical resistivity of the Cu/MWCNTs/ABS composites, because Cu that could locate between MWCNTs chain segments provides a better charge transport in the conductive pathways. Compared with pure ABS, the tensile strength, elastic modulus and thermal stability of the Cu/MWCNTs/ABS composites were significantly improved with the incorporation of Cu and MWCNTs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41738.

In this article, submicron and micron calcium copper titanate (CCTO) crystallites with different morphologies were successfully designed and prepared by directly thermal treatment method and molten salt method, respectively. Then, the silicone elastomer filled with self-prepared CCTO particles had high dieletric constant, low dielectric loss, and actuated strain which was greatly improved at low electric field. The dieletric constant at 50 Hz obviously increased from 2.15 for pure silicone elastomer to 4.37 and 4.18 for the submicron and micron CCTO/poly (dimethyl siloxane) (PDMS) composites. The dielectric loss of the composites retained at a low value (less than 0.06). Meanwhile, the elastic modulus of CCTO/PDMS composites was increased slightly only with a good flexibility. Compared to pure silicone elastomer (2.25%), the submicron and micron CCTO/PDMS composites with 2 wt % content exhibited a greater strain of 7.69% and 9.83% at a low electric field of 5 V/μm. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42613.

In this article, the ZnS/epoxy nanocomposites were successfully prepared by the reaction of zinc acetate and H₂S gas via a simple step. Epoxy resin acted as the matrix for the formation of ZnS nanoparticles (10–20 nm) in the reaction system and kept them from agglomerating. The structure, composition, and mechanical properties of the resultant products were successfully investigated by powder X-ray diffraction, transmission electron microscope, field emission scanning electron microscope, energy dispersive X-ray fluorescence, and universal testing machine. Meanwhile, by employing differential scanning calorimetry (DSC) we had studied, under nonisothermal condition, the kinetic analysis of the cure reaction which was performed using two classic models: Kissinger and Flynn-Wall-Ozawa. The activation energy of curing reaction was 74.63 kJ/mol and 77.57 kJ/mol, respectively, by Kissinger's and Flynn-Wall-Ozawa's methods. The possible mechanism of preparation of ZnS/epoxy composites was discussed in this article. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012

Polymer nanocomposites are usually made by incorporating dried nanoparticles into polymer matrices. This way not only leads to easy aggregation of nanoparticles but also readily brings about opaqueness for nanocomposites based on functionally transparent polymers. In this letter, transparent ZnO/epoxy nanocomposites with high-UV shielding efficiency were prepared via two simple steps: first, in situ preparation of zinc hydroxide (Zn(OH)₂)/epoxy from the reaction of aqueous zinc acetate (Zn(Ac)₂·2H₂O) and sodium hydroxide (NaOH) at 30°C in the presence of high-viscosity epoxy resin; second, thermal treatment of the as-prepared Zn(OH)₂/epoxy hybrid into ZnO/epoxy composites. Optical properties of the resultant ZnO/epoxy nanocomposites were studied using an ultraviolet–visible (UV–vis) spectrophotometer. The nanocomposites containing a very low content of ZnO nanoparticles (0.06 wt %) possessed the optimal optical properties, namely high-visible light transparency and high-UV light shielding efficiency. Consequently, the as-prepared ZnO/epoxy nanocomposites are promising for use as novel packaging materials in lighting emitting diodes technology. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012

Poly(ethylene terephthalate)/expanded graphite conductive composites were prepared by the melt-blending method. The relationships between the preparation methods, microstructures, and conductivity properties of the composites were studied with scanning electron microscopy and conductivity measurements. The results showed that the composites presented a low percolation threshold and strong anisotropic conductivity. The epoxy resin had a strong intercalation effect on the expanded graphite that led to the easy formation of the conductive network. With classical statistical percolation theory, the conductivity behaviors of the composites were investigated. The results indicated that the nonuniversal critical exponent should be attributed to the anisotropy of conductivity, the tunneling conduction, and the particular structure. In addition, preliminary studies on the crystallization and dynamic mechanical behavior of the composites were performed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008