The binding of a target analyte to an ion channel (IC), which is readily detected electrochemically in a label-free manner with single-molecule selectivity and specificity, has generated widespread interest in using natural and engineered ICs as transducers in biosensing platforms. To date, the majority of developments in IC-functionalized sensing have focused on IC selectivity or sensitivity or development of suitable membrane environments and aperture geometries. Comparatively little work has addressed analytical performance criteria, particularly criteria required for temporal measurements of dynamic processes. We report a measurement protocol suitable for rapid, time-resolved monitoring (≤30 ms) of IC-modulated membrane conductance. Key features of this protocol include the reduction of membrane area and the use of small voltage steps (10 mV) and short duration voltage pulses (10 ms), which have the net effect of reducing the capacitive charging and decreasing the time required to achieve steady state currents. Application of a conductance protocol employing three sequential, 10 ms voltage steps (−10 mV, −20 mV, −30 mV) in an alternating, pyramid-like arrangement enabled sampling of membrane conductance every 30 ms. Using this protocol, dynamic IC measurements on black lipid membranes (BLMs) functionalized with gramicidin A were conducted using a fast perfusion system. BLM conductance decreased by 76 ± 7.5% within 30 ms of switching from solutions containing 0 to 1 M Ca2+, which demonstrates the feasibility of using this approach to monitor rapid, dynamic chemical processes. Rapid conductance measurements will be broadly applicable to IC-based sensors that undergo analyte-specific gating.

•Polymerized phospholipid bilayer chromatographic stationary phases were characterized.•Poly(lipid) stationary phases exhibit high chemical and mechanical stability.•Frontal chromatography shows lipophilic retention of model analytes.The ability to rapidly screen complex libraries of pharmacological modulators is paramount to modern drug discovery efforts. This task is particularly challenging for agents that interact with lipid bilayers or membrane proteins due to the limited chemical, physical, and temporal stability of conventional lipid-based chromatographic stationary phases. Here, we describe the preparation and characterization of a novel stationary phase material composed of highly stable, polymeric-phospholipid bilayers self-assembled onto silica microparticles. Polymer–lipid membranes were prepared by photochemical or redox initiated polymerization of 1,2-bis[10-(2′,4′-hexadieoyloxy)decanoyl]-sn-glycero-2-phosphocholine (bis-SorbPC), a synthetic, polymerizable lipid. The resulting polymerized bis-SorbPC (poly(bis-SorbPC)) stationary phases exhibited enhanced stability compared to particles coated with 1,2-dioleoyl-sn-glycero-phosphocholine (unpolymerized) phospholipid bilayers when exposed to chemical (50 mM triton X-100 or 50% acetonitrile) and physical (15 min sonication) insults after 30 days of storage. Further, poly(bis-SorbPC)-coated particles survived slurry packing into fused silica capillaries, compared to unpolymerized lipid membranes, where the lipid bilayer was destroyed during packing. Frontal chromatographic analyses of the lipophilic small molecules acetylsalicylic acid, benzoic acid, and salicylic acid showed >44% increase in retention times (P < 0.0001) for all analytes on poly(bis-SorbPC)-functionalized stationary phase compared to bare silica microspheres, suggesting a lipophilic retention mechanism. Phospholipid membrane-functionalized stationary phases that withstand the chemical and physical rigors of capillary LC conditions can substantially increase the efficacy of lipid membrane affinity chromatography, and represents a key advance toward the development of robust membrane protein-functionalized chromatographic stationary phases.

Black lipid membranes (BLMs) provide a synthetic environment that facilitates measurement of ion channel activity in diverse analytical platforms. The limited electrical, mechanical and temporal stabilities of BLMs pose a significant challenge to development of highly stable measurement platforms. Here, ethylene glycol dimethacrylate (EGDMA) and butyl methacrylate (BMA) were partitioned into BLMs and photopolymerized to create a cross-linked polymer scaffold in the bilayer lamella that dramatically improved BLM stability. The commercially available methacrylate monomers provide a simple, low cost, and broadly accessible approach for preparing highly stabilized BLMs useful for ion channel-functionalized analytical platforms. When prepared on silane-modified glass microapertures, the resulting polymer scaffold-stabilized (PSS)-BLMs exhibited significantly improved lifetimes of 23 ± 9 to 40 ± 14 h and >10-fold increase in mechanical stability, with breakdown potentials >2000 mV attainable, depending on surface modification and polymer cross-link density. Additionally, the polymer scaffold exerted minimal perturbation to membrane electrical integrity as indicated by mean conductance measurements. When gramicidin A and α-hemolysin were reconstituted into PSS-BLMs, the ion channels retained function comparable to conventional BLMs. This approach is a key advance in the formation of stabilized BLMs and should be amenable to a wide range of receptor and ion channel functionalized platforms.Keywords: black lipid membrane; gramicidin; ion channel; lipid bilayer; methacrylate polymer; polymer scaffold; α-hemolysin

Transmembrane protein (TMP)-functionalized materials have resulted in powerful new methods in chemical analysis. Of particular interest is the development of high-throughput, TMP-functionalized stationary phases for affinity chromatography of complex mixtures of analytes. Several natural and synthetic phospholipids and lipid mimics have been used for TMP reconstitution, although the resulting membranes often lack the requisite chemical and temporal stability for long-term use, a problem that is exacerbated in flowing separation systems. Polymerizable lipids with markedly increased membrane stability and TMP functionality have been developed over the past two decades. More recently, these lipids have been incorporated into a range of analytical methods, including separation techniques, and are now poised to have a significant impact on TMP-based separations. Here, we describe current methods for preparing TMP-containing stationary phases and examine the potential utility of polymerizable lipids in TMP affinity chromatography.

The sensitivity and selectivity of ion channels provide an appealing opportunity for sensor development. Here, we describe ion channel probes (ICPs), which consist of multiple ion channels reconstituted into lipid bilayers suspended across the opening of perflourinated glass micropipets. When incorporated with a scanning ion conductance microscope (SICM), ICPs displayed a distance-dependent current response that depended on the number of ion channels in the membrane. With distance-dependent current as feedback, probes were translated laterally, to demonstrate the possibility of imaging with ICPs. The ICP platform yields several potential advantages for SICM that will enable exciting opportunities for incorporation of chemical information into imaging and for high-resolution imaging.

The development of next-generation transmembrane protein-based biosensors relies heavily on the use of black lipid membranes (BLMs); however, electrical, mechanical, and temporal instability of BLMs poses a limiting challenge to biosensor development. In this work, micrometer-sized glass apertures were modified with silanes of different chain length and fluorine composition, including 3-cyanopropyldimethychlorosilane (CPDCS), ethyldimethylchlorosilane (EDCS), n-octyldimethylchlorosilane (ODCS), (tridecafluoro-1, 1, 2, 2-tetrahydrooctyl)dimethylchlorosilane (PFDCS), or (heptadecafluoro-1,1,2,2-tetrahydrodecyl)dimethylchlorosilane (PFDDCS), to explore the effect of substrate surface energy on BLM stability. Low energy silane-modified surfaces promoted enhanced lipid–substrate interactions that facilitate the formation of low-leakage, stable BLMs. The surface energies of silane-modified substrates were 30 ± 3, 16 ± 1, 14 ± 2, 11 ± 1, and 7.1 ± 2 mJ m–2 for CDCS, EDCS, ODCS, PFDCS, and PFDDCS, respectively. Decreased surface energy directly correlated to improved electrical, mechanical, and temporal BLM stability. Amphiphobic perfluorinated surface modifiers yielded superior performance compared to traditional hydrocarbon modifiers in terms of stability and BLM formation, with only marginal effects on BLM membrane permeability. Leakage currents obtained for PFDCS and PFDDCS BLMs were elevated only 10–30%, though PFDDCS modification yielded >5-fold increase in electrical stability as indicated by breakdown voltage (> 2000 mV vs 418 ± 73 mV), and >25-fold increase in mechanical stability as indicated by air–water transfers (> 50 vs 2 ± 0.2) when compared to previously reported CPDCS modification. Importantly, the dramatically improved membrane stabilities were achieved with no deleterious effects on reconstituted ion channel function, as evidenced by α-hemolysin activity. Thus, this approach provides a simple, low cost, and broadly applicable alternative for BLM stabilization and should contribute significantly toward the development of next-generation ion-channel-functionalized biosensors.Keywords: aperture; black lipid membrane; membrane stability; silane-modified surface; surface energy;

Robust and high-density biosensors incorporating suspended lipid membranes require microfabricated apertures that can be readily integrated into complex analysis systems. Apertures with well-defined, three-dimensional geometries enable the formation of suspended lipid membranes and facilitate reduced aperture size compared to vertical-walled apertures. Unfortunately, existing methods of producing apertures with well-defined, three-dimensional geometries are based on complex and expensive fabrication procedures, some of which yield apertures in excessively fragile thin-film materials. Here, we describe a microfabrication method utilizing incline and rotate lithography that achieves sloped-wall microapertures in SU-8 polymer substrates with precision control of the aperture diameter, substrate thickness, and wall angle. This approach is simple, is of low cost, and is readily scaled up to allow highly reproducible parallel fabrication. The effect of the incident angle of UV exposure and the size of photomask features on the aperture geometry were investigated, yielding aperture diameters as small as 7 μm and aperture wall angles ranging from 8° to 36° measured from the normal axis. Black lipid membranes were suspended across the apertures and showed normalized conductance values of 0.02–0.05 pS μm–2 and breakdown voltages of 400–600 mV. The functionality of the resulting sloped-wall microapertures was validated via measurement of reconstituted α-hemolysin activity and the voltage-gated channel activity of alamethicin.

Unilamellar phospholipid vesicles prepared using the polymerizable lipid bis-sorbylphosphatidylcholine (bis-SorbPC) yield three-dimensional nanoarchitectures that are highly permeable to small molecules. The resulting porous phospholipid nanoshells (PPNs) are potentially useful for a range of biomedical applications including nanosensors and nanodelivery vehicles for cellular assays and manipulations. The uniformity and size distribution of the pores, key properties for sensor design and utilization, have not previously been reported. Fluorophore-assisted carbohydrate electrophoresis (FACE) was utilized to assess the nominal molecular weight cutoff limit (NMCL) of the PPN via analysis of retained dextran with single monomer resolution. The NMCL of PPNs prepared from pure bis-SorbPC was equivalent to a 1800 Da linear dextran, corresponding to a maximum pore diameter of 2.6 nm. Further investigation of PPNs prepared using binary mixtures of bis-SorbPC and dioleoylphosphatidylcholine (DOPC) revealed a similar NMCL when the bis-SorbPC content exceeded 30 mol %, whereas different size-dependent permeation was observed below this composition. Below 30 mol % bis-SorbPC, dextran retention provided insufficient mass resolution (162 Da) to observe porosity on the experimental time scale; however, proton permeability showed a marked enhancement for bis-SorbPC ≥ 10 mol %. Combined, these data suggest that the NMCL for native pores in bis-SorbPC PPNs results from an inherent property within the lipid assembly that can be partially disrupted by dilution of bis-SorbPC below a critical value for domain formation. Additionally, the analytical method described herein should prove useful for the challenging task of elucidating porosity in a range of three-dimensional nanomaterials.

Nanomaterials have rapidly moved into the mainstream for chemical and biological analysis. Nanoparticle probes enhance signal intensity, increase the chemical and physical stability of the probe, and facilitate surface modification for specific targeting. Unfortunately, common problems are encountered with many nanoparticle probes, e.g., poor solubility, poor biocompatibility, and leakage of encapsulated components, that severely restrict the application of probes to ex vivo samples under carefully controlled conditions. A wide range of recently developed multifunctional nanomaterials are poised to make significant contributions to molecular analysis of biological systems. Composite nanoparticle geometries, including composites, hybrids, and core–shell nanoparticles prepared using two or more materials, e.g., silica/inorganic, silica/polymer, or polymer/inorganic combinations, offer improved solubility, easier functionalization, and decreased toxicity compared with the related single-component materials. Furthermore, composite nanomaterials present substantial signal amplification, and improved multiplexing for higher-sensitivity and higher-resolution measurements. Further development and integration of composite nanomaterials into the quantitative sciences will play a key role in the future of functional probes for imaging, quantitative analysis, and biological manipulation.

The stabilization of suspended planar lipid membranes, or black lipid membranes (BLMs), through polymerization of mono- and bis-functionalized dienoyl lipids was investigated. Electrical properties, including capacitance, conductance, and dielectric breakdown voltage, were determined for BLMs composed of mono-DenPC, bis-DenPC, mono-SorbPC, and bis-SorbPC both prior to and following photopolymerization, with diphytanoyl phosphocholine (DPhPC) serving as a control. Poly(lipid) BLMs exhibited significantly longer lifetimes and increased the stability of air−water transfers. BLM stability followed the order bis-DenPC > mono-DenPC ≈ mono-SorbPC > bis-SorbPC. The conductance of bis-SorbPC BLMs was significantly higher than that of the other lipids, which is attributed to a high density of hydrophilic pores, resulting in relatively unstable membranes. The use of poly(lipid) BLMs as matrices for supporting the activity of an ion channel protein (IC) was explored using α-hemolysin (α-HL), a model IC. Characteristic i−V plots of α-HL were maintained following photopolymerization of bis-DenPC, mono-DenPC, and mono-SorbPC, demonstrating the utility of these materials for preparing more durable BLMs for single-channel recordings of reconstituted ICs.

Suspended planar lipid membranes (or black lipid membranes (BLMs)) are widely used for studying reconstituted ion channels, although they lack the chemical and mechanical stability needed for incorporation into high-throughput biosensors and biochips. Lipid polymerization enhances BLM stability but is incompatible with ion channel function when membrane fluidity is required. Here, we demonstrate the preparation of a highly stable BLM that retains significant fluidity by using a mixture of polymerizable and nonpolymerizable phospholipids. Alamethicin, a voltage-gated peptide channel for which membrane fluidity is required for activity, was reconstituted into mixed BLMs prepared using bis-dienoyl phosphatidylcholine (bis-DenPC) and diphytanoyl phosphatidylcholine (DPhPC). Polymerization yielded BLMs that retain the fluidity required for alamethicin activity yet are stable for several days as compared to a few hours prior to polymerization. Thus, these polymerized, binary composition BLMs feature both fluidity and long-term stability.

Black lipid membranes (BLMs) are widely used for recording the activity of incorporated ion channel proteins. However, BLMs are inherently unstable structures that typically rupture within a few hours after formation. Here, stabilized BLMs were formed using the polymerizable lipid bis-dienoyl phosphatidylcholine (bis-DenPC) on glass pipettes of ∼10 μm (I.D.). After polymerization, these BLMs maintained steady conductance values for several weeks, as compared to a few hours for unpolymerized membranes. The activity of an ion channel, α-hemolysin, incorporated into bis-DenPC BLMs prior to polymerization, was maintained for 1 week after BLM formation and polymerization. These lifetimes are a substantial improvement over those achievable with conventional BLM technologies. Polymerized BLMs containing functional ion channels may represent an enabling technology for development of robust biosensors and drug screening devices.

Nanometre-sized, chemically-stabilized phospholipid vesicle sensors have been developed for detection of dissolved molecular oxygen. Sensors were prepared by forming 150 nm phospholipid vesicles from 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) or DOPC doped with small (<1%) mole percentages of 1,2-dioleoyl-sn-glycero-3-phosphoethanol amine-N-(7-nitro-2-1,3-benzoxadiazol-4-yl) (NBD-PE). Sensors were stabilized via cross-linking polymerization of hydrophobic methacrylate monomers partitioned into the hydrophobic interior of the DOPC bilayer. The resultant unilamellar, nanometre-sized, polymer–lipid vesicles are spherical, biocompatible and protect sensing components that are loaded into the aqueous interior of the vesicle from interfering species in the exterior environment. For O2 detection, the oxygen-sensitive fluorescent dye, tris(1,10-phenanthroline)ruthenium(II) chloride (Ru(phen)3) was encapsulated into the aqueous interior of the polymerized phospholipid vesicle. NBD-PE was introduced into the phospholipid bilayer of the sensor as a reference dye, allowing ratiometric sensors to be constructed. The resultant sensors show high sensitivity, excellent reversibility and excellent linearity over a physiological range of dissolved oxygen concentrations. These results suggest that polymerized phospholipid vesicle sensors can be used for monitoring intracellular O2 dynamics.

In this letter, we report a facile method to prepare robust phospholipid vesicles using commonly available phospholipids that are stabilized via the formation of an interpenetrating, acid-labile, cross-linked polymer network that imparts a site for controlled polymer destabilization and subsequent vesicle degradation. The polymer network was formed in the inner lamella of the phospholipid bilayer using 2,2-di(methacryloyloxy-1-ethoxy)propane (DMOEP) and butyl methacrylate (BMA). Upon exposure to acidic conditions, the highly cross-linked polymer network was partially converted to smaller linear polymers, resulting in substantially reduced vesicle stability upon exposure to chemical and physical insults. Isolated polymers had pH-dependent-solubility in THF. Transmission electron microscopy and dynamic light scattering revealed time-dependent enhanced vesicle stability in high concentrations of surfactant and vacuum conditions at elevated pH, whereas exposure to acidic pH rapidly decreased the vesicle stability, with complete destabilization observed in less than 24 h. The resultant transiently stabilized vesicles may prove useful for enhanced drug delivery and chemical sensing applications and allow for improved physiological clearance.