Molybdenum oxide nanomaterials have recently attracted widespread attention for their unique optical properties and catalytic performance. However, until now, there is little literature on the application of photoluminescent molybdenum oxide nanomaterials in biological and pharmaceutical sensing. Herein, photoluminescent molybdenum oxide quantum dots (MoOx QDs) were synthesized via a facile method, and then, the synthesized MoOx QDs were further applied as a new type of photoluminescent probe to design a new off–on sensor for captopril (Cap) determination on the basis of the fact that the quenched photoluminescence of MoOx QDs by Cu2+ was restored with Cap through specific interaction between the thiol group of Cap and Cu2+. Under optimal conditions, the restored photoluminescence intensity showed a good linear relationship with the content of Cap, ranging from 1.0 to 150.0 μM, with a limit of detection of 0.51 μM (3σ/k). Additionally, the content of Cap in pharmaceutical samples was successfully detected with the newly developed off–on sensor, and the recoveries were 99.4–101.7%, which suggest that the present off–on sensor has a high accuracy.Topics: Luminescence; Luminescence; Quantum dots;

A new route for one-pot preparation of carbon dots (CDs) was developed at room temperature using PEG400 as both the carbon source and passitive agent. The new method possesses the advantages of facile, rapid, energy-saving, without any external stimulus and environment friendly. By changing the content of NaOH, the PEG400-CDs with blue-emitting, yellow-emitting, orange red-emitting and red-emitting were obtained, and the formation mechanism were carefully investigated. In addition, a sensitive fluorescence sensor were developed for Fe2+ detection based on PEG400-CDs since the fluorescence of PEG400-CDs could be enhanced by Fe2+. It was found that there is a good linear relationship between the enhanced fluorescence and Fe2+ concentration in the range of 0.5 to 2.0 μmol·L−1 with the detection limit of 6.0 × 10−8 mol·L−1, and Fe2+ in water samples was also determined with high accuracy and repeatability.

As a well-studied transition-metal semiconductor material, MoOx has a wider band gap than molybdenum disulfide (MoS2), and its property varies dramatically for the existence of several different allotropes and suboxide phases of molybdenum oxides (MoOx, x < 3). In this manuscript, a one-pot method possessing the advantages of one pot, easily prepared, rapid, and environmentally friendly, has been developed for facile synthesis of highly photoluminescent MoOx quantum dots (MoOx QDs), in which commercial molybdenum disulfide (MoS2) powder and hydrogen peroxide (H2O2) are employed as the precursor and oxidant, respectively. The obtained MoOx QDs can be further utilized as an efficient photoluminescent probe, and a new turn-off sensor is developed for 2,4,6-trinitrotoluene (TNT) determination based on the fact that the photoluminescence of MoOx QDs can be quenched by the Meisenheimer complexes formed in the strong alkali solution through the inner filter effect (IFE). Under the optimal conditions, the decreased photoluminescence of MoOx QDs shows a good linear relationship to the concentration of TNT ranging from 0.5 to 240.0 μM, and the limit of detection was 0.12 μM (3σ/k). With the present turn-off sensor, TNT in river water samples can be rapidly and selectively detected without tedious sample pretreatment processes.Keywords: 2,4,6-trinitrotoluene; inner filter effect; Meisenheimer complexes; MoOx quantum dots; photoluminescent sensor; turn-off

•Though increasing effort has been devoted to MoOx nanomaterials synthesis, only a few reports mentioning its photoluminescence property are available, while even no evidence has shown its applications in chemical and biological sensing.•Herein, a one-pot method possessing the advantages of rapid, easily prepared and environment friendly was developed for facile synthesis of highly photoluminescent MoOx quantum dots, which was further utilized to construct a new off-on sensor for phosphate determination in complicated lake water samples.Molybdenum oxide (MoOx) is a well-studied transition-metal semiconductor material, and has a wider band gap than MoS2 which makes it become a promising versatile probe in a variety of fields, such as gas sensor, catalysis, energy storage ect. However, few MoOx nanomaterials possessing photoluminescence have been reported until now, not to mention the application as photoluminescent probes. Herein, a one-pot method is developed for facile synthesis of highly photoluminescent MoOx quantum dots (MoOx QDs) in which commercial molybdenum disulfide powder and hydrogen peroxide (H2O2) are involved as the precursor and oxidant, respectively. Compared with current synthesis methods, the proposed one has the advantages of rapid, one-pot, easily prepared, environment friendly as well as strong photoluminescence. The obtained MoOx QDs is further utilized as an efficient photoluminescent probe, and a new off-on sensor has been constructed for phosphate (Pi) determination in complicated lake water samples, attributed to the fact that the binding affinity of Eu3+ ions to the oxygen atoms from Pi is much higher than that from the surface of MoOx QDs. Under the optimal conditions, a good linear relationship was found between the enhanced photoluminescence intensity and Pi concentration in the range of 0.1–160.0 μM with the detection limit of 56 nM (3σ/k). The first application of the photoluminescent MoOx nanomaterials for ion photochemical sensing will open the gate of employing MoOx nanomaterials as versatile probes in a variety of fields, such as chemi-/bio-sensor, cell imaging, biomedical and so on.