The two step sequential deposition of CH3NH3PbI3-based perovskite solar cells has been modified by applying toluene and chlorobenzene vapors during the preparation of PbI2 films leading to the growth of the PbI2 grain size. PbI2 films treated with these solvent vapors have more surface area with which CH3NH3I can react leading to a more desirable perovskite layer morphology. This resulted in a significant increase in the performance of the corresponding perovskite solar cell devices where the average power conversion efficiency was enhanced from 5.2% for the control device up to 8.4 and 10.2% for toluene and chlorobenzene-treated devices, respectively.

The performance of organic photovoltaic devices is improving steadily and efficiencies have now exceeded 10%. However, the incident solar spectrum still largely remains poorly absorbed. To reduce optical losses, we employed a microlens array (MLA) layer on the side of the glass substrate facing the incident light; this approach does not interfere with the processing of the active-layer. We observed up to 10% enhancement in the short circuit current of poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl] thieno[3,4-b]thiophenediyl}):(6,6)-phenyl C71-butyric acid methyl ester (PTB7:PC71BM) OPV cells. Theoretically and experimentally investigating several MLA dimensions, we found that photocurrent increases with the ratio of the height to the pitch size of MLA. Simulations reveal the enhancement mechanisms: MLA focuses light, and also increases the light path within the active-layer by diffraction. Photocurrent enhancements increase for a polymer system with thinner active-layers, as demonstrated in poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT):PC71BM OPVs with 17% improvement in short circuit current.

We experimentally and theoretically investigate the effects of utilizing BaTiO3 nanoparticles as additives in polythiophene/fullerene solar cells. BaTiO3 nanoparticles were chosen because of their multifaceted potential for increasing exciton dissociation (due to their high dielectric constant) and light scattering. To achieve stable suspensions for device fabrication, the nanoparticles were functionalized with organic ligands. Solar cells fabricated in air showed ∼40% enhancement in the photocurrent primarily due to string-like aggregates of functionalized BaTiO3 particles that increase light absorption without hindering charge collection. Solar cells fabricated in an inert atmosphere yielded overall more efficient devices, but the string-like aggregates were absent and enhancement in photocurrent was up to ∼6%. Simulations with the excitonic drift-diffusion model demonstrate that a bare nanoparticle significantly increases exciton dissociation, whereas the functional group negates this effect. Simulations utilizing the scattering matrix method reveal that absorption enhancements caused by light scattering increase as the nanoparticles aggregate into string-like structures. These results offer insights for morphological design of ternary-blend bulk-heterojunction organic solar cells.

In organic electronic devices, indium tin oxide (ITO) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) are the most common transparent electrode and anodic buffer layer materials, respectively. A widespread concern is that PEDOT:PSS is acidic and etches ITO. We show that this issue is not serious: only a few nanometers of ITO are etched in typical device processing conditions and storage thereafter; conductivity losses are affordable; and optical transmission gains further offset these losses. Organic photovoltaic (OPV) devices fabricated on old ITO (with PEDOT:PSS history) were similar or higher in efficiency than devices on fresh ITO. Poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7) devices on old ITO showed efficiencies up to 9.24% compared to 8.72% efficient devices on fresh ITO. This reusability of ITO can be impactful for economics of organic electronics because ITO accounts for almost 90% of energy embedded in devices, such as OPVs.Keywords: etching; indium tin oxide; PEDOT:PSS; polymer solar cells; transparent electrode

In any microelectronic device, fundamental physical parameters must be well understood for successful electronic optimization. One such prominent parameter is energetic trap states, which are well-known to plague amorphous or otherwise impure semiconducting materials. Organic semiconductors are no strangers to such states and their electronic properties are evidently tied to these defects. Herein, this article discusses the identification, characterization and mitigation of bandgap residing trap levels in organic photovoltaic devices. A compilation of select studies to date is given and a general outlook is proposed. Organic photovoltaic materials are depicted as multiple trap-level systems with a seemingly continuous distribution of electronic states throughout the bandgap. Some elucidations as to the origins of these electronic states as well as recent works centered on defect removal are also presented.

Over the last decade, polymer solar cells (PSCs) have attracted a lot of attention and highest power conversion efficiencies (PCE) are now close to 10%. Here we employ an optical structure – the microlens array (MLA) – to increase light absorption inside the active layer, and PCE of PSCs increased even for optimized devices. Normal incident light rays are refracted at the MLA and travel longer optical paths inside the active layers. Two PSC systems – poly(3-hexylthiophene-2,5-diyl):(6,6)-phenyl C61 butyric acid methyl ester (P3HT:PCBM) and poly[[9-(1-octylnonyl)-9H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl]:(6,6)-phenyl C71 butyric acid methyl ester (PCDTBT:PC70BM) – were investigated. In the P3HT:PCBM system, MLA increased the absorption, absolute external quantum efficiency, and the PCE of an optimized device by ∼4.3%. In the PCDTBT:PC70BM system, MLA increased the absorption, absolute external quantum efficiency, and PCE by more than 10%. In addition, simulations incorporating optical parameters of all structural layers were performed and they support the enhancement of absorption in the active layer with the assistance of MLA. Our results show that utilizing MLA is an effective strategy to further increase light absorption in PSCs, in which optical losses account for ∼40% of total losses. MLA also does not pose materials processing challenges to the active layers since it is on the other side of the transparent substrate.

•We utilize low-boiling-point solvent additives to improve morphology of polymer solar cells.•Utilizing a low-boiling-point additive tetrahydrofuran resulted in better charge extraction.•Additive led to polymer-fullerene demixing and lower leakage currents.•Effect was largely insensitive to slight variations in boiling point and solvent's dipole moment.•Effect appears to be general to more material systems.Processing organic photovoltaic (OPV) blend solutions with high-boiling-point solvent additives has recently been used for morphological control in bulk-heterojunction OPV cells. Here we show that even low-boiling-point solvents can be effective additives. When P3HT:PCBM OPV cells were processed with a low-boiling-point solvent tetrahydrafuran as an additive in parent solvent o-dichlorobenzene, charge extraction increased leading to fill factors as high as 69.5%, without low work-function cathodes, electrode buffer layers or thermal treatment. This was attributed to PCBM demixing from P3HT domains and better vertical phase separation, as indicated by photoluminescence lifetimes, hole mobilities, and shunt leakage currents. Dependence on solvent parameters and applicability beyond P3HT system was also investigated.

A key requirement for realizing efficient organic photovoltaic (OPV) cells is the dissociation of photogenerated electron-hole pairs (singlet-excitons) in the donor polymer, and charge-transfer-excitons at the donor–acceptor interface. However, in modern OPVs, these excitons are typically not sufficiently harnessed due to their high binding energy. Here, we show that doping the OPV active-layers with a ferroelectric polymer leads to localized enhancements of electric field, which in turn leads to more efficient dissociation of singlet-excitons and charge-transfer-excitons. Bulk-heterojunction OPVs based on poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester are fabricated. Upon incorporating a ferroelectric polymer as additive in the active-layer, power conversion efficiencies increase by nearly 50%, and internal quantum efficiencies approach 100% – indicating complete exciton dissociation at certain photon energies. Similar enhancements in bilayer-heterojunctions, and direct influence of ferroelectric poling on device behavior show that improved dissociation is due to ferroelectric dipoles rather than any morphological change. Enhanced singlet-exciton dissociation is also revealed by photoluminescence lifetime measurements, and predicted by simulations using a numerical device model.

Herein, the implications of silicone contamination found in solution-processed conjugated polymer solar cells are explored. Similar to a previous work based on molecular cells, we find this contamination as a result of the use of plastic syringes during fabrication. However, in contrast to the molecular case, we find that glass-syringe fabricated devices give superior performance than plastic-syringe fabricated devices in poly(3-hexylthiophene)-based cells. We find that the unintentional silicone addition alters the solution’s wettability, which translates to a thinner, less absorbent film on spinning. With many groups studying the effects of small-volume additives, this work should be closely considered as many of these additives may also directly alter the solutions’ wettability, or the amount of silicone dissolved off the plastic syringes, or both. Thereby, film thickness, which generally is not reported in detail, can vary significantly from device to device.Keywords: organic; P3HT; PDMS; photovoltaic; plastic; polymer; silicone; solar;

Over the last decade, polymer solar cells (PSCs) have attracted a lot of attention and highest power conversion efficiencies (PCE) are now close to 10%. Here we employ an optical structure – the microlens array (MLA) – to increase light absorption inside the active layer, and PCE of PSCs increased even for optimized devices. Normal incident light rays are refracted at the MLA and travel longer optical paths inside the active layers. Two PSC systems – poly(3-hexylthiophene-2,5-diyl):(6,6)-phenyl C61 butyric acid methyl ester (P3HT:PCBM) and poly[[9-(1-octylnonyl)-9H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl]:(6,6)-phenyl C71 butyric acid methyl ester (PCDTBT:PC70BM) – were investigated. In the P3HT:PCBM system, MLA increased the absorption, absolute external quantum efficiency, and the PCE of an optimized device by ∼4.3%. In the PCDTBT:PC70BM system, MLA increased the absorption, absolute external quantum efficiency, and PCE by more than 10%. In addition, simulations incorporating optical parameters of all structural layers were performed and they support the enhancement of absorption in the active layer with the assistance of MLA. Our results show that utilizing MLA is an effective strategy to further increase light absorption in PSCs, in which optical losses account for ∼40% of total losses. MLA also does not pose materials processing challenges to the active layers since it is on the other side of the transparent substrate.

The performance of organic photovoltaic devices is improving steadily and efficiencies have now exceeded 10%. However, the incident solar spectrum still largely remains poorly absorbed. To reduce optical losses, we employed a microlens array (MLA) layer on the side of the glass substrate facing the incident light; this approach does not interfere with the processing of the active-layer. We observed up to 10% enhancement in the short circuit current of poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl] thieno[3,4-b]thiophenediyl}):(6,6)-phenyl C71-butyric acid methyl ester (PTB7:PC71BM) OPV cells. Theoretically and experimentally investigating several MLA dimensions, we found that photocurrent increases with the ratio of the height to the pitch size of MLA. Simulations reveal the enhancement mechanisms: MLA focuses light, and also increases the light path within the active-layer by diffraction. Photocurrent enhancements increase for a polymer system with thinner active-layers, as demonstrated in poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT):PC71BM OPVs with 17% improvement in short circuit current.

The two step sequential deposition of CH3NH3PbI3-based perovskite solar cells has been modified by applying toluene and chlorobenzene vapors during the preparation of PbI2 films leading to the growth of the PbI2 grain size. PbI2 films treated with these solvent vapors have more surface area with which CH3NH3I can react leading to a more desirable perovskite layer morphology. This resulted in a significant increase in the performance of the corresponding perovskite solar cell devices where the average power conversion efficiency was enhanced from 5.2% for the control device up to 8.4 and 10.2% for toluene and chlorobenzene-treated devices, respectively.