The smart surface created in a microfluidic chip has shown the capability of adsorbing and releasing proteins under electrical control. The inner surface of the chip channel was first coated by a thin layer of Au through sputtering and was subsequently modified with loosely packed self-assembled monolayers (SAMs) of thiols with terminal carboxylic or amino groups. Upon application of an external electric potential to the gold substrate, reversible conformational transformation between “bent” and “straight” states for the anchored mercapto chains could be modulated, through the electrostatic effect between the ionized terminal groups and the charged gold substrate. Thus, a hydrophobic or hydrophilic channel surface was established and could be reversibly switched electrochemically. Accordingly, the microchips prepared in this way can reversibly and selectively adsorb and release differently charged proteins under electrical control. Two model proteins, avidin and streptavidin, were demonstrated to be readily adsorbed by the smart chips under negative and positive potential, respectively. Also, more than 90 % of the adsorbed proteins could be released upon an electrical command. Furthermore, these chips were applied to the controlled separation of avidin and streptavidin mixtures with 1:1 and 1:1000 molar ratios. Under specific applied potentials, the chips adsorbed a certain protein from the mixture whereas the other protein was allowed to flow out, after which the adsorbed protein could be released by switching the applied potential. Thus, two eluted protein fractions were obtained and the separation of the two proteins was achieved. For the former mixture, each eluted fraction contained up to ≈80–90 % avidin or streptavidin. For the latter mixture, the resulting separation efficiency indicated that the molar ratio of avidin and streptavidin could be increased from 1:1000 to about 32:1 after five run separations.

Isolation and identification of natural products is a very important and active research field. However, establishing the purity of the samples during the isolation process is quite difficult, especially when the retention times are similar for two desired components in HPLC. Although some technologies, e. g. MS and NMR, offer effective ways of obtaining purity information about the samples, the expensive instrumentation required or the off-line nature of coupling (generally speaking) make purity analysis somewhat inconvenient. In this paper, an on-line analytical system coupling HPLC and a CCD spectrometer for determination of purity for each eluate was developed in a thin layer spectrometric cell. The effectiveness of the system was demonstrated by differentiating Tanshinone I, Tanshinone IIA, and their mixture. The time-resolved UV-Vis spectra promptly revealed significant differences between the three samples while conventional single wavelength detection (CSWLD) could not. The system was then used to distinguish two steroid compounds which behaved as a single component in CSWLD. The compounds were isolated from a Chinese marine invertebrate animal, a marine annelid, Arenicola cristata, referred to here as Stimpson. The method reported here provided an efficient, convenient, fast, and inexpensive approach holding promise for on-line determination of the purity of samples isolated from natural products.

Marine organisms are the important source of the bioactive metabolites. A novel enolic sulfated sterol, arenicolsterol A, has been isolated from a marine annelid Arenicola cristata collected in the coast of Mainland of China. The structure was elucidated using all sorts of spectroscopic data including ESIMS, 1D and 2D NMR etc. The cytotoxic bioactivity of this sterol was evaluated by MTT assay. It could inhibit the growth of human cervix cancer cell line (Hela) and human non-small cell lung cancer cell line (NCI-h6) with IC₅₀ of (3.1±0.6) µg/mL and (7.6±0.8) µg/mL.

The macroscopic properties of a surface can be intelligently controlled by alternating the states of the modified molecules, such as polymers, metallic oxide, or self-assembled monolayers (SAMs). This article reviews various approaches to create a switchable surface and different types of external stimuli used to switch the surface properties. This area is of potential benefit for biomaterials, biosensors, information storage, microfluidic systems, adhesive materials, nanolithography, and so on.